Debian下手动编译安装pure-ftpd

先从pure-ftpd网站上下载软件包,格式为tar.gz或tar.bz2,以pure-ftpd-1.0.21.tar.gz版本为例.   debian:/# tar -zxvf pure-ftpd-1.0.21.tar.gz           #在软件包所在目录下解压软件包. debian:/# cd pure-ftpd-1.0.21                         #进入解压后的目录. debian:/# ./configure --prefix=/usr/local/pureftpd    #指定安装路径. debian:/# make                                        #编译文件. debian:/# make install                                #编译文件后安装. debian:/# cd /pure-ftpd-1.0.21/configuration-file     #进入configuration-file目录 debian:/# cp pure-config.pl /usr/local/pureftpd/sbin/pure-config.pl #复制文件 debian:/# cp pure-ftpd.conf /usr/local/pureftpd/etc/pure-ftpd.conf  #复制文件 debian:/# mkdir /etc/rc.boot                         #新建rc.boot目录 debian:/# touch /etc/rc.boot/pureftpd.sh             #新建pureftpd.sh文件   debian:/# cat /etc/rc.boot/pureftpd.sh               #添加以下内容.
#!/bin/sh
/usr/local/pureftpd/sbin/pure-config.pl /usr/local/pureftpd/etc/pure-ftpd.conf   debian:/# chmod 755 /etc/rc.boot/pureftpd.sh                    #增加文件可执行权限. debian:/# ln -s /etc/rc.boot/pureftpd.sh /etc/rc2.d/S88pureftpd #加入开机启动. debian:/# ./etc/rc.boot/pureftpd.sh                             #执行文件或重启都行!     pure-ftpd日志记录设置/var/log/pureftpd.log   1)建立文件/var/log/pureftpd.log

2)修改/etc/rsyslog.conf

1>在这行的cron.none后面添加 ;ftp.none 使ftp的日志信息成私有
*.info;mail.none;authpriv.none;cron.none /var/log/messages
为
*.info;mail.none;authpriv.none;cron.none;ftp.none    /var/log/messages

2>在/etc/rsyslog.conf文件最后加上

#pureftp日志
ftp.* -/var/log/pureftpd.log

注意: 不要去掉/var前面的-号,否则日志会在/var/log/messages与/var/log/purefpd.log里各记录一份. 添加了-号,就只会记录在/var/log/purefptd.log内

3)使/etc/rsyslog.conf生效
[[email protected] ]# killall -HUP syslogd

到现在设置完毕,重启下pure-ftpd,现在在客户端登陆ftp试下

=============[附我的rsyslog.conf]==========================
#*.=info;*.=notice;*.=warn;\
        auth,authpriv.none;\
        cron,daemon.none;\
        mail,news.none;ftp.none -/var/log/messages #
# Emergencies are sent to everybody logged in.
#
*.emerg                         * #
# I like to have messages displayed on the console, but only on a virtual
# console I usually leave idle.
#
#daemon,mail.*;\
#       news.=crit;news.=err;news.=notice;\
#       *.=debug;*.=info;\
#       *.=notice;*.=warn       /dev/tty8 # The named pipe /dev/xconsole is for the `xconsole' utility.  To use it,
# you must invoke `xconsole' with the `-file' option:
#
#    $ xconsole -file /dev/xconsole [...]
#
# NOTE: adjust the list below, or you'll go crazy if you have a reasonably
#      busy site..
#
daemon.*;mail.*;\
        news.err;\
        *.=debug;*.=info;\
        *.=notice;*.=warn       |/dev/xconsole #pure-ftpd log
ftp.*                         -/var/log/pureftpd.log