Linux中SysRq的使用

时间：2007-06-29 来源：blue_stone

Linux中SysRq的使用

作者:blue_stone([email protected])
转载请注明出处: http://bluestone.cublog.cn

当Linux 系统不能正常响应用户请求时, 可以使用SysRq小工具控制Linux.

一 SysRq的启用与关闭

要想启用SysRq, 需要在配置内核时设置Magic SysRq key (CONFIG_MAGIC_SYSRQ)为Y. 对于支持SysRq的内核, /proc/sys/kernel/sysrq控制SysRq的启用与否. 如果/proc/sys/kernel/sysrq内容为0, 则SysRq被禁用; 如果/proc/sys/kernel/sysrq内容为1, 则SysRq被启用. 关于/proc/sys/kernel/sysrq的更多描述, 请参考<Kernel Source>/Documentation/sysrq.txt

可通过运行命令echo "0" >/proc/sys/kernel/sysrq和echo "1" >/proc/sys/kernel/sysrq暂时启用或禁用SysRq. 如果需要永久启用或者禁用SysRqs, 则可在/etc/sysctl.conf中设置kernel.sysrq = 1 (启用SsyRq)或kernel.sysrq = 0 (禁用SysRq)

二 SysRq的使用

SysRq的命令键有

'r' - Turns off keyboard raw mode and sets it to XLATE.

'k' - Secure Access Key (SAK) Kills all programs on the current virtual
 console. NOTE: See important comments below in SAK section.

'b' - Will immediately reboot the system without syncing or unmounting
 your disks.

'o' - Will shut your system off (if configured and supported).

's' - Will attempt to sync all mounted filesystems.

'u' - Will attempt to remount all mounted filesystems read-only.

'p' - Will dump the current registers and flags to your console.

't' - Will dump a list of current tasks and their information to your
 console.

'm' - Will dump current memory info to your console.

'0'-'9' - Sets the console log level, controlling which kernel messages
 will be printed to your console. ('0', for example would make
 it so that only emergency messages like PANICs or OOPSes would
 make it to your console.)

'e' - Send a SIGTERM to all processes, except for init.

'i' - Send a SIGKILL to all processes, except for init.

'l' - Send a SIGKILL to all processes, INCLUDING init. (Your system
 will be non-functional after this.)

'h' - Will display help ( actually any other key than those listed
 above will display help. but 'h' is easy to remember :-)

在终端上同时按Alt, SysRq和命令键则会执行SysRq命令, SysRq键就是"Prent Screen"健. 比如Alt+SysRq+b则重启机器.

如果使用telnet 或ssh连接到服务器则可以使用echo '<SysRq命令键>' > /proc/sysrq-trigger的方式执行SysRq命令, 比如echo 'b' > /proc/sysrq-trigger重启系统.

三常用的SysRq命令(序列)

3.1 重启机器的SysRq命令序列是 k(SAK) s(sync) u(umount) b(reboot)

3.2 显示内存信息的SysRq命令是m(memory)

3.3 显示当前任务信息的SysRq命令是t(task)

四参考材料

<Kernel Source>/Documentation/sysrq.txt: sysrq.txt最权威的文档, 最好参考当前运行的kernel附带的文档. 或者去http://lxr.linux.no/source/Documentation/sysrq.txt查看

Oracle Metalink Note 228203.1: Alt SysRq Keys Utility on Linux

相关阅读更多 +