华为路由器密码恢复

时间：2006-11-18 来源：eaper1980

1, 重新启动路由器（注意：由于您不能进入特权模式，因此只有通过对路由器先关机、再上电来启动路由器，一定要在网络空闲时操作，以免影响正常的工作）。
2，在启动时，屏幕出现“Press Ctrl-B to enter Boot Menu..”时键入“Ctrl＋b”进入路由器的下载界面。
3，输入Bootrom口令（默认为空，直接回车即可）。
4，出现“Boot menu
        1：Download application program
        2：Download Bootrom program
        3：Modify Bootrom password
        4：Exit the menu
        5：reboot
Enter your choice（1-5）：”
   键入“Ctrl＋P”，系统出现几个“＃”后，将再次回答本界面，这次，选择    “5”：“Reboot”，
5，路由器重新启动后，您将能直接进入特权用户模式，但路由器的特权用户口令并没有清除，您需要在配置模式下输入：“enable password XXX”来更改口令。注意：password 一定要写全，否则，将提示为错误的命令。

刚才提到，进入下载界面时要输入Bootrom口令。可是如果以前设置了Bootrom口令，现在记不得了，就只有输入Bootrom的通用口令进入下载界面。Bootrom的通用口令是：“WhiteLily2970013”，区分大小写。新版1 AR路由器BOOTROM9.07清除CONSOLE密码:
Press Ctrl-B to enter Boot Menu
  Please input Bootrom password:

  Boot Menu:
   1:  Download application program with XMODEM
   2:  Download application program with NET
   3:  Set application file type
   4:  Display applications in Flash
   5:  Clear application password
   6:  Start up and ignore configuration
   7:  Enter debugging environment
   8:  Boot Rom Operation Menu
   9:  Do not check the version of the software
   a:  Exit and reboot
Enter your choice(1-a):
选择5后选择a重启路由器
BOOTROM9.06
Boot Menu:
   1:  Download application program with XMODEM
   2:  Download application program with NET
   3:  Clear application password
   4:  Start up and ignore configuration
   5:  Enter debugging environment
   6:  Boot Rom Operation Menu
   7:  Do not check the version of the software
   8:  Exit and reboot
  Enter your choice(1-8):
选择3然后再选择8重启路由器
新版2

BOOTROM7.06
Boot Menu:
   1:  Download application program with XMODEM
   2:  Download application program with NET
   3:  Clear application password
   4:  Start up and ignore configuration
   5:  Enter debugging environment
   6:  Boot Rom Operation Menu
   7:  Do not check the version of the software
   8:  Exit and reboot
  Enter your choice(1-8):
选3后选8重启路由器

BOOTROM5.28

Press Ctrl-B to enter Boot Menu
  Please input Boot ROM password:

  Boot Menu:
   1:  Download application program with XMODEM
   2:  Download application program with NET
   3:  Clear configuration
   4:  Start up and ignore configuration
   5:  Boot ROM Operation Menu
   6:  Do not check the version of the software
   7:  Exit and reboot
   Enter your choice(1-7):
选3会清除配置,选4会忽略配置以出厂设置启动
启运完毕后将路由器配置DOWN下后更改密码后再导入