linux redhat9.0/fedora4.0下adsl上网和配置全过程
时间:2006-10-05 来源:czm9790
linux redhat9.0/fedora4.0下adsl上网和配置全过程 |
---|
作者:上上智 来源:不详 (2006-06-27 16:59:02) |
|
看了这么久的blog,我自写一点配置哈 现在有很多想学习linux的人, 就是因为不能配置上网,所以不想学习现在我从adsl配置到nat全过程如下: 1)安装rp-pppoe-3.5-2包 在安装系统时,对新用户一般选择全部安装的,那就安装了,以后rpm, 或者tarball了,这很方便,对初学者: eg: rpm -ivh rp-pppoe-3.5-2.rpm tarball 安装: tar zxvf rp-pppoe-3.5-2.tar.gz cd rp-pppoe-3.5-2 ./configure make make install 2)rp-pppoe-3.5-2配置 步骤: a) adsl-setup 出现: Welcome to the ADSL client setup. First, I will run some checks on your system to make sure the PPPoE client is installed properly... The following DSL config was found on your system: Device: Name: ppp0 Please enter the device if you want to configure the present DSL config (default ppp0) or enter 'n' if you want to create a new one: //这是我已经安装过了,主要是写文档:选择默认按回车 LOGIN NAME Enter your Login Name (default lanlgn409ldj@zgcnc): //这是我已经安装过了,:没有安装是输入adsl用户名 INTERFACE Enter the Ethernet interface connected to the ADSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethX, where 'X' is a number. (default eth0): //选择默认按回车 Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped. If you want the link to stay up permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with dynamic IP addresses. You may have some problems with demand-activated links. Enter the demand value (default no): //选择默认按回车 DNS Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide dynamic DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup. Enter the DNS information here: // 输入server自动得到dns,server的ip PASSWORD Please enter your Password: USERCTRL Please enter 'yes' (two letters, lower-case.) if you want to allow normal user to start or stop DSL connection (default yes): //选择默认按回车问你是否连接 Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security. If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port. The firewall choices are: 0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your machine. You are STRONGLY recommended to use some kind of firewall rules. 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway for a LAN Choose a type of firewall (0-2): //是否设置firwall Do you want to start this connection at boot time? Please enter no or yes (default no): //启动时是否连接 Do you want to start this connection at boot time? Please enter no or yes (default no): ** Summary of what you entered ** Ethernet Interface: eth0 User name: lanlgn409ldj@zgcnc Activate-on-demand: No DNS: Do not adjust Firewalling: NONE User Control: yes Accept these settings and adjust configuration files (y/n)? //是否写入配置文件里 选择 y 3)假如你是用别人的mac连接 1 redhat9.0改mac: ifconfig eth0 down ifconfig eth0 hw ether 5254ab323d51 ifconfig eth0 up ifup ppp0 2 fedora 4.0改mac: ifdown eth0 ifconfig eth0 hw ether 5254ab323d51 ifup eth0 ifup ppp0 & adsl-start 4)测试一下 ping www.baidu.com 5)做nat echo "1" > /proc/sys/net/ipv4/ip_forward //这很重要,路由转发 modprobe ip_tables modprobe ip_nat_ftp modprobe ip_nat_irc modprobe ip_conntrack modprobe ip_conntrack_ftp modprobe ip_conntrack_irc /sbin/iptables -F /sbin/iptables -X /sbin/iptables -Z /sbin/iptables -F -t nat /sbin/iptables -X -t nat /sbin/iptables -Z -t nat /sbin/iptables -P INPUT ACCEPT /sbin/iptables -P OUTPUT ACCEPT /sbin/iptables -P FORWARD ACCEPT /sbin/iptables -t nat -P PREROUTING ACCEPT /sbin/iptables -t nat -P POSTROUTING ACCEPT /sbin/iptables -t nat -P OUTPUT ACCEPT /sbin/iptables -t nat -A POSTROUTING -o ppp0 -s 192.168.0.0/24 -j MASQUERADE//不是adsl也可以把ppp0改成eth0 , 1一般网卡nat: [root@test root]# vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=dhcp BROADCAST=192.168.0.255 IPADDR=192.168.0.1 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes [root@test root]# vi /etc/sysconfig/network-scripts/ifcfg-eth0:0 DEVICE=eth0:0 BOOTPROTO=static BROADCAST=192.168..255 IPADDR=192.168.1.2 NETMASK=255.255.255.0 NETWORK=192.168..0 ONBOOT=yes 2 两块网卡nat: 只是那個 eth0:0 改成了 eth1 而已啦,其它都是一样的设置 6)dns 设置 在里面/etc/resolv.conf 把你的ip写入里面去 nameserver 192.168.0.1 然后重启要不然,客户机不能上网 (http://www.fanqiang.com) |
相关阅读 更多 +